Involute splines look like spur gears at first glance, yet they solve a completely different mechanical problem: transmitting high torque between coaxial shafts and hubs with zero slip. This guide explains the fundamentals of ISO 4156:2021 and how to generate production-ready spline CAD geometry and inspection sheets online.
EXT) and a hub (internal, INT) coaxially so all teeth share torque simultaneously.Although an involute spline shares the same geometric involute flank family as an involute spur gear, its mechanical purpose is the opposite. Spur gears connect two parallel shafts to change speed, direction, or torque ratio while teeth roll smoothly in and out of mesh. An involute spline, by contrast, rigidly or axially connects two coaxial parts — an external shaft and an internal hub — so they rotate together at a 1:1 ratio.
Compared with traditional rectangular keys or straight-sided splines, involute teeth distribute torque uniformly around the entire circumference and naturally self-center under load. Because tooth stresses sit along curved involute flanks and rounded roots rather than sharp keyway corners, involute splines carry higher torque in a smaller package with lower fatigue sensitivity.
Unlike general spur gears where designers often pick arbitrary coefficients or custom rack proportions, ISO 4156 splines rely on strictly standardized combinations so off-the-shelf broaches, form milling cutters, hobs, and inspection gauges match across suppliers.
| Element | Standard Options | Design Role |
|---|---|---|
| Geometry Type | External (EXT) / Internal (INT) | Defines whether teeth sit on the outer shaft or inside the mating bore. |
| Pressure Angle (αD) | 30°, 37.5°, 45° | Balances radial centering force, tooth stiffness, and thin-wall suitability. |
| Root Form | Fillet Root (R) / Flat Root (P) | R minimizes root stress concentration; P (30° only) leaves a flat root land. |
| Centering & Fit | Side Fit — Classes 4, 5, 6, 7 | Flanks control angular backlash and clearance (H internal; d–k external). |
| Units | Metric (mm) & Inch (in / DP) | Standardized in metric modules with full inch/DP display and CAD scaling support. |
In production, external splines are commonly cut using form milling cutters, gear hobs, or cold rolling, while internal splines are typically broached or shaped. Because there is no free rolling ratio modification like an arbitrary spur pair, the finished CAD profile should be exact.
Low-resolution polygon exports introduce faceting along flanks and roots that ruins CAM finishing passes and finite-element contact models. Exporting true analytical NURBS SPLINE and ARC entities ensures your 3D CAD model and toolpaths stay smooth.
On the shop floor, directly measuring chordal tooth thickness inside an internal hub or narrow space is impractical. Standard metrology therefore relies on calibrated cylindrical pins placed between opposite teeth — reported as Over Pins (MRe) for external splines and Between Pins (MRi) for internal splines — together with tolerance limits for both the active part and its mating counterpart.
Switch to External or Internal Involute Spline in GearProfile.app to preview exact 360° geometry and generate NURBS DXF & QC documentation.
Open Spline & Gear Generator →A spur gear transfers rotary motion and speed ratios across parallel shafts; an involute spline joins two coaxial components (shaft and hub) at a 1:1 ratio so all teeth transmit torque simultaneously.
30° is standard for general mechanical power transmission, 37.5° increases tooth-root strength in compact joints, and 45° is common on fine pitches where radial hub thickness is limited.
Fillet Root (R) joins flanks with a continuous full radius to reduce stress concentration and improve fatigue life. Flat Root (P) is available with 30° splines and uses corner fillets into a flat root circle.
They are standard shop-floor inspection dimensions measured across precision cylindrical pins placed in the tooth spaces, verifying effective tooth thickness or space width tolerance without direct flank gauging.
Standard splines rely on matching cutters, broaches, and go/no-go gauges. Restricting inputs to valid ISO 4156 combinations guarantees your CAD file matches real standardized tooling.
Related reading: Internal (Ring) Gear Generator · Involute Gear Profile Generator · Gear Module and Pressure Angle